2.5G RF Remoter for CCT adjustable and Dimmable for LED Lighting products from SWEET LEDS
By the end of Nov of 2013, We just released a new Lighting control system. 2.5G RF CCT adjutable and Dimmable lighting system.
This system mainly used in Indoor Lighting for higher quality requirement family or meeting room. It can work with Panel light, LED A19 bulbs, LED T8, LED Down light and etc. Pls check following information about it.
Color Temperature Adjustable and Dimmable Remoter and fixtures
2.4G RF Remoter
BATTERY ON THE BACK OF THE REMOTER
A wireless remote control is installed adjust the brightness of LED lighting color temperature adjustment (Note that when you install lighting and electrical connection , the need for qualified personnel to install and professional electrical connection )
• Turn off the power supply circuit.
· Lamps installed by the installation instructions , please check the power connection is correct.
· Energized after power is turned on if the lamp is lit properly , if not light , check the power supply and lighting .
2.3 wireless remote control adjust the color temperature adjusting brightness LED lamps and remote control code matching and packet control group at the same time : ( Tip : wireless remote tune the color temperature adjusting brightness LED lamps and remote control only after the codes match each other , the remote control to remote control the LED lights. remote control can be different lamp into different groups ( up to four ) , were controlled .
① Make sure the remote control battery and wireless remote tune the color temperature adjusting brightness LED lighting has been installed well .
② code matching and grouping
· Selected packet control the lights need to re- turn off the power for 10 seconds after the power supply is turned on in an instant (within 3 seconds ) click on the group button 3 times to open the lights will " slow flash three times ," confirmed matches packet success.
· Repeat the above steps until all the lights grouped want grouping .
③ using the remote control grouping
After completing the wireless remote tune the color temperature adjusting brightness LED lamps and remote control system code matching and grouping is complete, you can achieve the following wireless control .
• Turn on the lamp power .
· Click on "All On " button , all the lights turn on at the same time .
· Connect , click on the ' control panel ' may be dimming for all open at the same time , adjusting the color temperature. Brightness up and down keys are raised , lowered . Balmy cold left and right buttons to adjust the color . Any time press "All On " key , all the same to the brightest lights .
· Click on " All Off " button , all the lights off at the same time .
· Click on the appropriate "group on" key , the control objectives to the packet ,
· Use " in the control panel ' can light all of the group while dimming, color temperature adjustment up and down buttons to increase brightness , respectively lowered . Balmy cold left and right buttons to adjust the color .
· Press the "group on" key, you can set all the same to the brightest lights .
· Click on " grouping off" button can be assigned to the group while the lamp is turned off.
Tip 1: When you need to simultaneously control more than two , four or less light , you can first select the "full " button , all the lights turn on and then turn off unneeded while simultaneously control group, and then click on the ' control panel ' implementation operation.
Tip 2: If the lamp power , and wireless remote control adjust the color temperature adjusting brightness LED lamps are turned off remote control , wireless remote tune the color temperature adjusting brightness LED lamps is in standby mode, in standby mode , although the bulb does not light, but each lights still consumes about 0.5 watts.
Tip 3 : Remote LED lamp has a memory function , adjusted after each lamp appropriate brightness and color temperature , shut down , or turn off the power back on after that to restore the state of the power to shut down or cut off the lights before .
Note: The remote shutdown and then cut off the power , turn the power off state without memory , remote shutdown restored to the state before the lights ; under night light mode after shutdown or power off , reboot or no memory Nightlight state power , Nightlight mode returns to the state before .
· Follow the need to cut off the lamp power supply , or to keep the lamp power is turned on .
④ night light mode
Wireless remote tune the color temperature adjusting brightness LED lamps feature Nightlight function , night light, soft , soft like water, can produce effects similar to moonlight lighting to create a warm hazy lighting conditions , help people calm down and fall asleep can also be used as walkway lights to save power .
· Long press " full off " button , all the lights at the same time raised Nightlight mode.
· Long press " grouping off" button can be assigned to the group at the same time raised the lamp night light mode.
Tip: Each lamp night light mode consumes about 0.7 watts.
⑤ clear code and re- grouping
If you change the layout of the room , or use preferences change , you may need to change the previous packet , before regrouping remote LED lights need to address code cleared.
· Selected codes require clear lights, turn the power off the power after 10 seconds , turn on the power at the moment (within 3 seconds ) click on the " full " key or the key to open the corresponding group , five times , the lamp will " flash six under " Confirm clear success of the code .
• After the success of the Qing code regrouping operation of the process and consistent process ② " code matching and grouping " operation.
Three . Replace , add, and re-set
3.1 Replace battery
Replace the battery does not affect the pairing and grouping has been completed , installed after the new battery without any additional settings directly.
3.2 LED lights to replace or add Remote
When the end of the LED lamp life , or need to add a remote control LED lights, please follow the steps below to replace , newly installed remote LED lights need to re- code matching and grouping.
· Cut the need to replace or add Remote power LED lamp fixtures
· When installing lighting and electrical connection , the need for qualified personnel professional installation and electrical connection .
· Reference to "2.3 ② code matching and grouping " setting part
Replace or add Remote Control 3.3
After the new battery installed by remote control in accordance with the normal procedure to complete the pairing and grouping. (Refer to "2.3 ② code matching and grouping " section of settings )
Note: The wireless remote control tune the color temperature adjusting brightness LED lighting supports up to four remote control while matching , if the increase in the fourth over of the remote control and LED lamps on the time code matching , LED lights will automatically clear the first matching remote control data , and so on.
Four . Frequently Asked Questions
Question 1: wireless remote tune the color temperature adjusting brightness LED lamp power is on, but the remote control switch lights off , if power consumption ?
A: In this case , each lamp power consumption of about 0.5 watts.
Question 2 : A remote control can control how many lights ?
A: Each packet and the remote control can be received within a range with a number of different types of LED wireless remote tune the color temperature adjusting brightness LED lamps on the same control codes match .
Question 3 : Is it possible to use two or more remote control of one or a set of lights
A: You can use the remote control up to four simultaneous control .
Question 4: frequency control signals from the remote control and how much ?
A : The remote control according to the IEEE802.15.4 designed to control a distance of about 35 meters , the signal frequency is 2.4GHz.
Question 5 : You must use the remote control at the remote control LED lights when it?
A: No , using a radio frequency signal RF -based wireless protocol , the remote control and wireless remote tune the color temperature adjusting brightness LED lamps no physical obstacle between them.
Five . Common Faults and exclusion
Symptom one : Light did not respond to the remote control
Investigation suggested the following order :
· Check the lamp power is power.
· Check the remote control batteries are normal.
• Check whether the remote control light on the code pair.
Symptom 2 : lights automatically appear inexplicable actions
Possible reasons : It may be another remote control lights up
Troubleshooting Methods: According to "2.3 ⑥ clean code and re- grouping " steps
Dispose of used product in accordance with the rules and regulations of the local authorities
Remove the battery before discarding the remote control
Battery life can not be mixed and garbage , need to follow the requirements of the local environmental protection process
General lighting replaced with wireless remote tune the color temperature adjusting brightness LED lamps, you can use the remote control supporting wireless remote control, control light switches and adjusting brightness , color temperature . No additional wiring to install , simple and convenient.
Note: The wireless remote control tune the color temperature adjusting brightness LED lamps and remote control are separate systems , supporting only with the company's products are not compatible with other brands and the company's ordinary energy-saving lamps , incandescent lamps , LED lamps and remote control systems. A remote control within the reception range can adjust the color temperature adjustment for multiple wireless remote control brightness LED lamps. Remote Control Function Keys
Lighting Fixture available:
LED T8, LED Panel, LED A19 bulb, LED PAR30, PAR38, LED Down light and Ceiling Light.
or any other custom made LED lighting fixtures you want!!!